We’ve been pleased with the progress of the New Mantis project so far. Since this is a follow up to a product that has already hit the market, we shared our direction (post-Refine Phase) with some of our retail partners. While they liked some of what they saw, there was some feedback that made us take our foot off the gas and look into concepting again.
In light of that feedback, we’re opening up a Community Design Phase 2. Everyone (Community, Quirky, and retailers) agrees that the Mantis line should interact with your laptop or computer, and that the new Mantis should be smaller, but this time we want to also focus on the portable light aspect. When we say portable we don’t necessarily mean just another flashlight; we want you to think about possibilities for a whole new category of portable lights.
In light of that feedback, when you’re concepting for the new round, think about the following:
-How it is carried?
-How and where it is stored?
-What other situations and scenarios of use will make this a compelling product?
In terms of influence, we’ve awarded influence in the Community Design Phase to any of the submissions that helped feed into our Refine Phase submissions. In the Refine Phase we chose any submission that fed into the direction we chose that garnered us valuable feedback from retailers.
Recently, we put the stamp on HydraDuo that said “We’re Making It!”. Over a year has gone by since the product was designed and we have decided to revisit it. The new design reduces the amount of plastic, increases functionality, and makes it more aesthetically pleasing. The HydraDuo now includes two refillable plastic chambers held together with a thermoplastic rubber waist band and two removable leak proof mouth pieces. Water and Gatorade? Apple juice and orange juice? Rum and Coke? Carry one and drink two with HydraDuo.
Check out the new CMF phase and help us determine the best possible colors, materials, and finishes for the HydraDuo.
Ben will be hopping on Quirky’s uStream channel tonight (Wednesday) at 5:30pm EST for a live Q&A session. Now’s your chance to ask all the questions you’ve been dying to have answered… and if you know Ben, you know that everything’s fair game.
If you’ve got questions you want answered, add them to the comments on this blog post, or this thread in the forum.
To recap:
What: Ben answering all your deepest, darkest questions
There has been a lot of passionate debate about the design of product 175, the innovative trivets. Much of the controversy surrounds Louis Lara’s original design and the new direction that QDS has taken. Because of the overwhelming support, we’re re-exploring the possibilities of the original submission. New sketches will be added to the Refine Phase project for the community to evaluate, and influence will be awarded to Louis within the Concept Phase. Since we’re adding new material, the Refine timeline will also be extended.
The other design directions are still under consideration, and we’d really like the community to keep an open mind. To give everyone insight into why QDS went in a different direction, here’s a recap of this product’s design process:
QDS began by experimenting with a wide range of geometric tessellating patterns to expand upon Louis’ submission.
During market research and shape exploration, we found many existing trivets using tessellation designs.
That got us thinking. Was there something more unique that hadn’t been done before?
As QDS went through the Concept submissions from community members, they paid special attention to the potential of different shapes and materials for simplicity, ease of use, and user interaction. The approach described in Trivet Sticks, submitted by a community member, was chosen because it brought up a new way of achieving the results described by Louis. That concept led to the designs within the initial Refine Phase sketches. Even though the form had changed, those designs remained true to the original intent: the ability to reconfigure a trivet in new, exciting ways.
It’s clear from the community feedback that you think we just abandoned the original submission. So, we’re going back and making sure we preserve all the strong elements of the original design. The additional Refine Phase sketches (to be posted over the next few days) will focus on getting the best out of both winning concepts. When going through, tell us what you respond to in each option. We’re eager to create the best damn trivets in the world with your input!
Now that we’ve closed the concept phase for the auto-stirring microwave bowl we would like to update you on our prototyping progress. Thanks for all the ideas that were submitted! After testing several concepts utilizing the spinning of the turntable as well as the heat generated by the microwave, we feel that we are gradually narrowing in on a direction to move forward with. In addition to the challenges identified in our last update (material limitations, food density, turntable strength) we have begun to focus our attention on product simplicity, manufacturing, price, ease of use, and cleaning, with a better understanding of functional limitations.
The first concept was an attempt to use the motion of the turntable to create a continuous wobbling effect when a bowl is placed on a plastic plate supported only by a single point in the center. The idea was that the contents of the bowl would be agitated gradually when placed on the wobble plate. While this concept consists of only a single part that can be used with a variety of bowls, it proved to be not very effective.
The possibility for harnessing the heat of the microwave seemed promising, so a device was prototyped that would float inside the bowl and use steam propulsion to drive mixing paddles. This prototype consists of a sealed floatation chamber and a separate volume where water can be stored with several ports for emitting steam. The thought was that the water would boil inside the microwave creating a teapot effect at each of the ports, spinning the mixing paddles. After testing, it took too long for the contained water to heat up and generated very little force.
The thought of just inserting a spoon or spatula into the bowl during turntable rotation was worth a try. A model was made with an articulating arm fixed to the interior of the microwave with a suction cup. The articulating arm is adjustable to accommodate a variety of bowl shapes. The end could potentially be detachable and interchangeable. This simple idea did not provide enough of a mixing effect.
Using bits of the previous prototype, we then created an array of paddles attached to the lid of a bowl that would turn when impacting a point held fixed with a suction cup. The wings at the top of each paddle could impact anywhere along their length allowing for some flexibility with suction cup placement. The results were promising so we decided to pursue this further and create a version with gear driven paddles that would spin more continuously.
The following video describes this concept in more detail:
After a conversation with the inventor Michelle B. last Friday, it was agreed to move forward with the geared paddle concept. In addition to mechanism refinement, we will be considering possibilities for optional paddle shapes that may be interchangeable for use with different types of food. Our goal for the short term will be to focus on a simple mechanical solution with a minimum number of parts made from microwave safe materials. In the long term we will continue to research other more advanced and technically challenging ways of stirring inside a microwave oven.
If you have any comments or suggestions, feel free to add them in the comments of this blog post.
The Concept Phase for Ryan Campagna’s adjustable baking tray has launched and we are pumped to see what types of concepts get submitted. This product is all about user experience and workflow, so don’t hesitate to get into the kitchen and allow your observations to dictate your concept directions. We are going to open this concept round up to the community before the QDS team dives in too deeply. We know we have some experienced bakers in our community and we want to see how you would approach this product. Additionally, we are also excited to see how areas of interest outside of the kitchen, such as camping and origami, may inspire the adjustable feature.
You might have heard that this week we’ve locked up our design staff in the loony bin front window of Bed Bath & Beyond on 6th Avenue.
Since they’ve got their hands full (of sharpies and sketch paper and stuff), at this point we’re not planning on doing a regular Wednesday brainstorm session.
Instead, get involved with the fun happening at Bed Bath & Beyond. You can find all of the details right here.
While Product 157 started as a “Soap Dispensing Pet Brush”, after doing some research and testing we’ve decided to go a different direction. We’re getting rid of the soap dispensing feature in favor of creating a product that focuses on the entire workflow of washing your pet.
As we explored a number of different directions submitted in the concept round, we were inspired by Jason Hennessy’s idea of having an ambidextrous, one size fits all hand mitt with soft and hard bristles. We found that having both allows for a more thorough cleaning. Through our research and testing, we also found that the workflow that Dave Fulton described in his submission was the more natural and easier way to wash a dog.
The design we’re proceeding with is composed of two units, a pre-wash dry brush for removing dead hair and stimulating skin, and a silicone hand mitt for the bathing.
Here are a few more reasons for the change:
• The soap dispensing feature adds an unnecessary step in the washing work flow.
• Soap volume will not be enough for a wide range of dog sizes
• Professional groomers usually use their hands when bathing a dog (support for the silicone hand mitt) for a more intimate/calming experience for the dog.
• Groomers recommend to pre-brush your pet before washing to remove any dead hair and to stimulate blood flow.
• The two units in the chosen design fit together for practical storage.
Here’s the design we’re working with:
Feel free to participate in the (just launched) CMF phase for this product, right here!
2. Pay attention to your interactions. One of the best ways to arrive at a true problem solving concept is to really examine the problems at hand… so go ahead and pick up a heavy pot of water, play around with your gardening tools, etc… and see what types of problems you run into.
3. Ask yourself some questions, such as:
a. Depending on the task and the product in use, where is the pain located?
b. If you have arthritis or a similar condition, what helps you perform tasks in the kitchen?
c. What are your thoughts on your current kitchen products? What do you like or not like about them and how could they be improved?
d. Does the strain in your hand come from the holding of the weight, lifting, tilting or rotating?
We are not looking for you to answer these questions specifically, but rather for you to use these types of questions (these are just some examples… many questions pertain!) to help you draw inspiration from your personal experiences.